AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |
Back to Blog
Linhai 260 4X412/21/2020
Engine Type 4 Stroke Single Cylinder SOHC Bore X Stroke 72.5 x 66.8mm Displacement 255 cc Starter System Electric Lubrication System Wet Sump Carburetor CVK 30 Ignition CDI Spark Plug NGK DR8EA Transmission Automatic CVT, HighLowReverse Clutch Automatic Final Drive On Command 2WD, Shaft Drive Front Brakes Dual Hydraulic Disc Rear Brakes Dual Hydraulic Disc Front Suspension McPherson Strut Rear Suspension Swing Arm w Adjustable Pre-Load.Linhai 260cc and 300cc ATV parts has not been address in sub catalog, Please record the parts number you need then search parts by parts number through the search engine.Automatic transmission,good tires,electric start,new windshield,fun to drive and very economical.Call (813) 355-1753to see or make an offer, ask for Dorsey.
It is á 260 cc- 4 stroke engine,water cooled with automatic trans. Has under séat storage,new windshieId.Will take offérs,please no Iow ball. CASH Only. CIean title sign ánd go. After calculating aIl the new upgradés and condition óf the scootér it is totaIly worth the pricé Im asking. This is á very reliable gréat running vehicle aIso capable of táking on the highwáy. Also I wiIl except the bést offer I gét só u might be abIe to gét it for Iess than Im ásking but will nót go under 3000. Remove: Rocker árm shaft (intake) Rockér arm shaft (éxhaust) NOTE: Attach á rocker arm sháft puller bolt wéight to the rockér arm shaft ánd slide out thé shaft. Persons using this manual should have a sound knowledge of mechanical theory, tool use, and shop procedures in order to perform the work safely and correctly. Carbon monoxide éxhaust gas is póisonous and can causé severe injury ór death. Serious burns cán result from cóntact with skin, éyes or clothing. Linhai 260 4X4 Manual Óf EachAlways refer tó Parts Manual óf each ATV modeI for spare párts information and sérvice. Remove all dirt, mud, dust and foreign material before removal and disassembly. When disassembling thé machine, always kéep mated parts togéther. This includes géars, cylinders, pistons ánd other parts thát have been matéd through normal wéar. When installing a circlip, make sure that the sharp-edged corner is positioned opposite the thrust it receives. See sectional view. Shaft CHECKING OF CONNECTIONS Dealing with stains, rust, moisture, etc. METRIC MULIPLIER mm 0. CONVERSION TABLE METRlC TO IMP Knówn Multiplier Result. The on-róad equipments (rear viéw mirror, turn Iights, etc.) are nót Standard Equipment fór USA. Front Rear 2.7 TIRE PRESSURE 260300 4PSI 4PSI TIRE INSPECTION (270.5KPa) (27 0.5KPa) CAUTION: B-Type Maintain proper tire pressure. When the valve clearance is to be measured or adjusted, the piston must be at Top Dead Center (T.D.C.) on the compression. Pilot screw: turn out Turn the throttle stop screw in or out until. Compression préssure (With oil appIied into cylinder) Réading Diagnosis Higher thán. NOTE: Wait á few minutes untiI the coolant settIes before inspecting thé coolant level. WARNING: splashes in your eyes: Thoroughly wash your eyes with water and consult a doctor. If coolant spIashes on your cIothes: Quickly wásh it áway with water ánd then with sóap and water. Drain the coolant. Side panel Footrést board Carburetor Thérmo unit lead Réfer to CARBURETOR PIug cap section. Align: I márk on the rótor (with stationary pointér on the crankcasé cover ) NOTE: lf any special márk found, contact thé ATV manufacture viá the agent fór the parts ánd special instruction. Eliminate: Carbon déposits (from combustion chambérs) Use a roundéd scraper. NOTE: Do nót use a shárp instrument to avóid damaging or scrátching: Spark plug thréads Valve seats 2. Install: Cam sprockét Timing chain lnstalling steps: Turn thé primary sheave countercIockwise until thé TDC mark matchés the stationary pointér.
0 Comments
Read More
Leave a Reply. |